SATA2 (M) 15pin  Y-Cable Convert to 2 x SATA2 15pin (F) 8 in

SATA2 (M) 15pin Y-Cable Convert to 2 x SATA2 15pin (F) 8 in

PST-3 Digital Power Supply Tester 20/24pin 4p 8p FDD SATA

PST-3 Digital Power Supply Tester 20/24pin 4p 8p FDD SATA
$19.00
Availability: In stock
SKU
ACTO01PST3

Feature:                    

  • ATX PSU each output connectors check
     
  • Tests 20-pin and 24-pin power supplies
     
  • Tests SATA power
     
  • Tests Pentium 4 power connector
     
  • Tests PCI-Express power connectors
     
  • Tests Xeon power connectors
     
  • Tests Floppy drive connectors
     
  • Tests standard 4-pin power supply connectors
     
  • Accurate voltage indicator +/-V(+12V1/+5V/+3.3V/5VSB/+12V2/-12V)
     
  • ATX P.G value display.
     
  • Lower or higher P.G values alarm
     
  • Lower voltage detected alarm.
     
  • Over voltage alarm.
     
  • No voltage detected alarm.
     
  • Dimension : H * L *D : 64mm * 150mm * 18mm


Manual:

1. Plug-in 24pin and plug-in (P4 / P6 or P8) connector into the tester before turn on power.
   - 20pin ATX PSU: use P4 connector.
   - 24pin ATX PSU: use P6 connector.
   - EPS PSU: use P8 connector.
2. Turn on your power supply
3. LCD show each voltage and P.G value on the screen automatic and you can hear 2 beep sounds.
4. ATX power output connector checking one by one.
  - If power output is working, the LED will light on
  - If power output failed, the LED will not light on.
5. Plug-in (HDD/Floppy) connector and check LED light. (+12V1/+5V).
6. Plug-in SATA connector and check LED light (+12V1/+5V/+3.3V).
7. Remove the connector after your checking.
8. DO NOT plug-in 2 connectors in to the tester at the same time. ( Only 24pin and (P4/P6/P8)
9. Abnormal voltage detected will not display on the screen.
10. No voltage detect, "LL" will display on the screen.
11. Detected Voltage lower than Min. value, "LL" will display on the screen.
12. Detected voltage higher than Max. value, "HH" will display on the screen.
13. When detected voltage is lower than table value (A), will alarm.
14. When detected voltage is higher than table value (B), will alarm.
15. P.G value detected lower 100ms or higher 900ms, P>G value is abnormal and alarm.

When abnormal power is detected an alarm sounds and the troubled readings blink on the screen.

Each voltage normal range:
Reference field Low (A) and High (B)
+/-5%: +5V, +5VSB, +3.3V
+/-10%: +12V1, +12V2, -12V

Normal Voltage Range
 
Display Voltage Range
 
Low (A)
 
High (B)
 
Min. (C)
 
Max. (D)
 
+5V
 
+4.75V
 
+5.25V
 
4.0V
 
6.0V
 
-12V
 
-11V
 
-13V
 
-10V
 
-14V
 
+12V1
 
+11V
 
+13V
 
+10V
 
+14V
 
+12V2
 
+11V
 
+13V
 
+10V
 
+14V
 
3.3V
 
+3.14V
 
+3.47V
 
+2.0V
 
+4.5V
 
5VSB
 
+4.75V
 
+5.25V
 
+4.0V
 
+6.0V
 
P.G
 
  0ms
 
990ms
 

Note:
The -5V DC output is took off from Intel ATX12V design guide since the 1.2 version.
1. The -5V usage was for last generation ISA slot. But the old ISA had been phased out since 1993~1994.
2. Neither P3 nor P4 systems will need -5V output.  

Warning:
This product is designed only for power supply output tests. Do not leave it connected to the power supply unattended. It
generates heat and could possibly damage your power supply.

More Information
Brand Generic
Manufacturer Part # ACTO01PST3
SKU ACTO01PST3
Write Your Own Review
You're reviewing:PST-3 Digital Power Supply Tester 20/24pin 4p 8p FDD SATA